[GUEST ACCESS MODE: Data is scrambled or limited to provide examples. Make requests using your API key to unlock full data. Check https://lunarcrush.ai/auth for authentication information.]

@kaizen3dprints Avatar @kaizen3dprints Kaizen 3D Prints

Kaizen 3D Prints posts on YouTube about treat, level, the first, has been the most. They currently have XXXXXX followers and XX posts still getting attention that total XXXXXX engagements in the last XX hours.

Engagements: XXXXXX #

Engagements Line Chart

Mentions: XX #

Mentions Line Chart

Followers: XXXXXX #

Followers Line Chart

CreatorRank: XXXXXXX #

CreatorRank Line Chart

Social Influence

Social topic influence treat 2.38%, level 2.38%, the first 2.38%, has been 2.38%, the latest 2.38%, batch 2.38%, tpu 2.38%, u1 XXXX%

Top accounts mentioned or mentioned by @snapmaker @inslogic @timeplastinc @amolen3dofficial

Top Social Posts

Top posts by engagements in the last XX hours

"3D printing with wood PLA from @inslogic"
YouTube Link 2025-12-11T03:11Z 10.5K followers, 5171 engagements

"Warning - Trypophobia trigger ahead. Optical treat with a 3D printed airless tennis ball and water"
YouTube Link 2025-12-12T02:48Z 10.5K followers, 4647 engagements

"What happens if your Timeplast filament is too wet Smoke"
YouTube Link 2025-12-11T20:35Z 10.5K followers, 5662 engagements

"How do I swap nozzles on the Bambu Lab H2C Vortek system"
YouTube Link 2025-12-11T05:08Z 10.5K followers, 7211 engagements

"Here is my first semi successful benchy using filament from @TimeplastINC"
YouTube Link 2025-12-12T22:26Z 10.5K followers, XXX engagements

"How do I power the Bambu Lab AMS X so I can print and dry at the same time"
YouTube Link 2025-10-28T01:23Z 10.5K followers, 23K engagements

"I don't think my PVA filament was dry enough 😅"
YouTube Link 2025-12-11T04:48Z 10.5K followers, 16.1K engagements

"I just finished my first Gridfinity drawer and I'm hooked"
YouTube Link 2025-12-11T23:59Z 10.5K followers, 4928 engagements

"How to connect via LAN mode on the Snapmaker U1"
YouTube Link 2025-12-12T02:23Z 10.5K followers, 1279 engagements

"3D printed textiles on the Snapmaker U1 and Bambu Lab P2S"
YouTube Link 2025-12-04T05:47Z 10.5K followers, 43.8K engagements

"How I fixed the @Snapmaker U1 when the toolheads couldn't be picked up or parked - part 2"
YouTube Link 2025-11-25T21:59Z 10.5K followers, 2309 engagements

"Part X of how I fixed the @Snapmaker U1 when the toolheads would not park properly"
YouTube Link 2025-11-25T22:11Z 10.5K followers, 2049 engagements

"I'm comparing the Snapmaker U1 with the Bambu Lab P2S - Round 2"
YouTube Link 2025-12-05T19:34Z 10.5K followers, 11K engagements

"How do I manually bed level the Snapmaker U1 Bed leveling wizard"
YouTube Link 2025-11-30T04:54Z 10.5K followers, 2945 engagements

"Here is the first overnight print on the Snapmaker U1"
YouTube Link 2025-11-28T05:32Z 10.5K followers, 5476 engagements

"What does a 3D printed textile look like on the @Snapmaker U1"
YouTube Link 2025-11-30T19:03Z 10.5K followers, 12.6K engagements

"The Bambu Lab H2C has been unboxed and calibrated. Time to put it to work"
YouTube Link 2025-12-09T21:08Z 10.5K followers, 15.5K engagements

"My first multi material print on the Snapmaker U1. TPU 95a and PEBA"
YouTube Link 2025-12-07T06:25Z 10.5K followers, 10.4K engagements

"How do I sew with 3D printed textiles"
YouTube Link 2025-12-10T05:16Z 10.5K followers, 5249 engagements

"3D printed Santa Claus hat v2"
YouTube Link 2025-12-08T04:46Z 10.5K followers, 4939 engagements

"Printing up a ball from PEBA filament from @amolen3d_official with the @Snapmaker U1"
YouTube Link 2025-12-09T17:26Z 10.5K followers, 4892 engagements

"I just recieved the latest batch of Timeplast filament to test. Stay tuned"
YouTube Link 2025-12-11T18:43Z 10.5K followers, 4697 engagements

"Bambulab H2D with TPU for AMS in the AMS HT drying filament"
YouTube Link 2025-06-03T00:44Z 10.5K followers, 56.8K engagements

"Small but mighty upgrade to the Bambu Lab P2S - a little cleanout ramp"
YouTube Link 2025-10-14T20:10Z 10.5K followers, 162.3K engagements

"Sliced time vs actual print time on the Snapmaker U1 using Snapmaker Orca"
YouTube Link 2025-12-03T04:58Z 10.5K followers, 3061 engagements

"How do I load in TPU 95a into a Bambu Lab H2S"
YouTube Link 2025-10-30T23:40Z 10.5K followers, 23.4K engagements

"3D printing a sandal on the Prusa XL with TPU 90A from Inslogic"
YouTube Link 2025-10-08T01:15Z 10.5K followers, 5070 engagements

"New Santa Claus hat model now uploaded to my Thangs account"
YouTube Link 2025-12-11T02:21Z 10.5K followers, 1604 engagements

"Tuesday morning 3D printed textile bag update"
YouTube Link 2025-12-09T19:06Z 10.5K followers, 4863 engagements

"Here are the basic steps for 3D printing textiles"
YouTube Link 2025-12-06T19:21Z 10.5K followers, 264K engagements

"Setting up multiple ams units to the different heads on the Bambu Lab H2C"
YouTube Link 2025-12-13T01:22Z 10.5K followers, 1326 engagements

"Snapmaker U1 toolhead failing to park - part 1"
YouTube Link 2025-11-25T06:28Z 10.5K followers, 24.5K engagements

"How do I replace the extruder gears on a Bambu Lab P series 3D printer"
YouTube Link 2025-12-12T17:56Z 10.5K followers, XXX engagements