[GUEST ACCESS MODE: Data is scrambled or limited to provide examples. Make requests using your API key to unlock full data. Check https://lunarcrush.ai/auth for authentication information.]

@Stocko Avatar @Stocko Stocko 👊🤖

Stocko 👊🤖 posts on X about 12v, has been, $8585t, electrical the most. They currently have XXXXX followers and XXX posts still getting attention that total XXXXX engagements in the last XX hours.

Engagements: XXXXX #

Engagements Line Chart

Mentions: XX #

Mentions Line Chart

Followers: XXXXX #

Followers Line Chart

CreatorRank: XXXXXXX #

CreatorRank Line Chart

Social Influence #

Social topic influence 12v #11, has been 0.54%, $8585t 0.54%, electrical 0.54%, arc 0.54%, electronics 0.54%, im a 0.54%, compact 0.54%, chips #1035

Top accounts mentioned or mentioned by @yacinemtb @ilyashairline @i2cjak @phethers @cooperzurad @harsh86400 @erebiuswhite @greggoriesmom @moonl88537 @fangsystems @msanterre @stocko @moondreamai @b1t3lf @barbogdafinka @ctrlssh @1972parzival @aspacen @lukebayes @danadvantage

Top Social Posts #

Top posts by engagements in the last XX hours

"@harsh86400 sorry but that's not listed on the unitree website as a valid application"
X Link @Stocko 2025-10-14T18:28Z 5953 followers, XX engagements

"Day 15: It's been a crazy day here long story. but this evening I've finished out the breadboard. I just need to solder up a barrel connector for the 12v side"
X Link @Stocko 2025-10-15T02:11Z 5961 followers, 8737 engagements

"does nature have an analog for this where an organism temporarily enters another organism and radically changes its behavior"
X Link @Stocko 2025-10-12T01:27Z 5961 followers, 7468 engagements

"Day 12: Vacation is over. I'm back in the lab and ready to build. I'll validate this circuit today but first I need to finish coupling the motor to the encoder for feedback"
X Link @Stocko 2025-10-11T14:35Z 5954 followers, 5736 engagements

"Fitting everything on to a board this size (green) has been really challenging. I think it can be done but that the cost of everything goes up to get really tiny parts (about triple). So I'm thinking why not orient the board differently to get more length"
X Link @Stocko 2025-10-04T18:31Z 5954 followers, 7967 engagements

"@BarbogDaFinka off to a good start"
X Link @Stocko 2025-10-15T14:28Z 5952 followers, XX engagements

"the next version of KiCad needs to just be footprint updates. like. wtf is text this large doing on the fab layer in 2025"
X Link @Stocko 2025-10-05T03:10Z 5954 followers, 1029 engagements

"@IterIntellectus black spray paint to the camera"
X Link @Stocko 2025-10-13T14:03Z 5953 followers, XXX engagements

"so many EE gatekeepers out there. makes it hard to break into the in crowd tbh"
X Link @Stocko 2025-09-27T13:51Z 5954 followers, 5124 engagements

"@BarbogDaFinka barbog hedge fund arc"
X Link @Stocko 2025-10-15T13:52Z 5961 followers, XXX engagements

"@i2cjak @lukebayes pretty crazy that they don't make X layer boards. for X layers would you do gnd/sig/pwr/pwr/sig/gnd"
X Link @Stocko 2025-10-12T22:51Z 5924 followers, XXX engagements

"my dad heard i was getting into electronics and gave me this"
X Link @Stocko 2025-10-05T17:40Z 5961 followers, 83.7K engagements

"LAWD AMIGHTY IT FITS IT ALL FITS"
X Link @Stocko 2025-10-07T01:40Z 5954 followers, 6983 engagements

"I've started routing the board. This might end up being a trial run though because I haven't validated the circuit yet. Also I decided to keep the 12V power routed as fat traces on the bottom layer due to the buck and switching noise and stuff"
X Link @Stocko 2025-10-13T03:17Z 5955 followers, 7725 engagements

"@DanAdvantage i'm trying lol. i'm a swe by trade. learning all this ee stuff in order to build robots"
X Link @Stocko 2025-10-15T02:45Z 5954 followers, XX engagements

"@CruiseandCoffee a compact brushed dc servo motor controller"
X Link @Stocko 2025-10-12T19:48Z 5927 followers, XX engagements

"how do i calculate the current tolerance for a CAN bus termination resistor at first i thought just ohm's law but what's the voltage of a differential signal"
X Link @Stocko 2025-10-05T19:05Z 5952 followers, 1431 engagements

"I'm going to go ahead and try a X layer board. Stackup will be signal ground signal power ground signal"
X Link @Stocko 2025-10-12T23:05Z 5954 followers, 13.1K engagements

"finally arrived today. solid tinned copper. 22AWG works great with my breadboard. the green one is the smallest i can make with my strippers so it's good that i also got the premade jumpers for short distances"
X Link @Stocko 2025-10-14T00:14Z 5954 followers, 2723 engagements

"this is how it should be. no one should be cursed to waste their precious mortality on menial tasks like this"
X Link @Stocko 2025-09-14T18:19Z 5949 followers, 3344 engagements

"the position sensor it uses is costs XX cents"
X Link @Stocko 2025-09-24T03:35Z 5946 followers, 24.1K engagements

"when the next carrington event hit you're going to want to have an #only7400 guy local to you to bootstrap civilization again"
X Link @Stocko 2025-10-12T17:27Z 5925 followers, 1592 engagements

"Day 13: So I'm thinking about a X layer PCB that's sig/gnd/pwr/sig Is it ok to split the power plane into two voltage levels (since I have two voltages in here) I've arranged the chips in a way where there isn't any 3v3 stuff on the 12-24v side"
X Link @Stocko 2025-10-12T19:34Z 5951 followers, 8235 engagements